Equipment upgrade (to existing telecoms facility) adding ancillary equipment to support the operation of existing antennas as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.

Swap 3 antennas as per plans and as per code.

Add (3) antennas. Swap (1) 60amp breaker with (1) 80amp breaker. As per plan and as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Original permit description:(com2014-02268)adding(3) antennas (3) radio remote units (3)fiber cables as per plans and as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Adding(3) antennas (3) radio remote units (3)fiber cables as per plans and as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Removing three existing antennas on an existing monopole and replacing them with three dual band antennas as per plans and as per code.

Install (1) microwave dish as per plans and as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Reconnect electric circuitry (2 circuits) for freestanding sign referenced on permit # com2013-00121 as per code.

"replace faces on existing free standing sign total of 4 sq. Ft. As per plans sign ""a"" 162 sf sign ""b"" sq. Ftsign ""c"" 112 sftsign ""d"" 116 sft. Connect sign ""b"" . Work per code and per drawings."

Installation of (12) twevle low voltage security system devices as per code

(use) use portion of first floor as of esisting structure (approx. 12 0 sq. Ft.) as a nightclub (tavern-including live entertainment/dancing) per pud ord 86-688.

"install voice evacuation system in night club "" whiskey jack"" connect to existing building fire alarm low voltage only."

Interior work 15 sqft: run fiber conduit from basement to roof top install fiber control box on roof top. As per plans & as per code.

Amend permit#com2011-19997 issued on 12-5-11 w/completion date of 6-5-12 to extend for 6 months. (also must amend to add hvac contractor for hvac work)original permit description:(com2011-19997)interior work; 2 2 sq ft; interior work non structural al

Non-structural alterations/exterior work - remove and replace (6) existing antennas on existing structure. Antenna will be located at same rad center as existing. Install 1 gps. As per plans as per code. If installing suppression system in equipment cabin

Request for time extension on permit# com2011-17205 issued on 08/08/11 with original/amended completion date of 02/08/12original permit description:(com2011-17205)replace 3 existing toilets with new toilets. Replace existing bath hand sinks with new si

Remove/replace (3) unmanned equipment cabinets on rooftop. Remove/replace (5) antennas on rooftop and add (1) antenna to existing mont on rooftop. As per plans as per code. If installing suppression system in equipment cabinet then a separate permit is r

Amend permit # com2011-19997 issued on 12-05-11 with plans # 2011-1357 to change electrical contractor. Original permit description:(com2011-19997)interior work; 2 2 sq ft; interior work non structural alterations partition framing. Replace interior

Interior work; 2 2 sq ft; interior work non structural alterations partition framing. Replace interior doors and walls office walls same size/location. Frame office walls ticket booth coatroom 4 bar areas per attached plans. Install suspended (d

Replace 18 existing ceiling lights replace 24 existing receptacles replace 8 switches. All equipment same size and location. Work done to code.

Replace 3 existing long counter & tops same size and location. As per code. No partition framing.

"replace 3 existing toilets with new toilets. Replace existing bath hand sinks with new sinks. Replace 3 existing floor sinks with new floor sinks. Replace of existing 3/4"" copper water lines with new tubing. All equipment same size/location as per"

Interior work (12 0 sq ft) - category i - non-structural alterations - interior demolition (remove non-bearing wall drywall ceiling tiles flooring and removal of debris and/or equipment) as per code. Separate permit required for tenant fitout

Install additional panel antennas & microwave dishes and (1) equipment cabinet/ platform on roof of existing telecom facility per plans & per code.

Amend permit#com2010-23464 issued on 12-16- with plans# 2010-1416 to add prime contractor as listed above. Original permit description:(com2010-23464)install 3 new antennas at an existing at&t telecommunication facility on the penthouse wall and antenna

Install 3 new antennas at an existing at&t telecommunication facility on the penthouse wall and antenna sled mount on roof. Install 1 cabinet on existing equipment platform. If installling supression system in equipment cabinet(s) then a separate permit i

"add 2 amp sub panel - install (1) 125 amp 277v breaker in existing switchgear. Install (1) 1 1/4"" conduit to new subpanel location. Install a 50kva transformer to get 120/240v 2 amps. Install new 2 a panel. Relocate (1) ckt from existing panel to n"

Amend permit # com2009-23107 issued on 10-22-09 with plans # 2009-1305 to add the following additional work: 9 low voltage devices as per code. Original permit description:(com2009-23107)remove and replace 9 panel antennas mounted to an existingbuilding r

Amend permit # com2009-23107 issued on 10/22/09 with plans # 2009-1305 to add contractor as listed aboveoriginal permit description:(com2009-23107)remove and replace 9 panel antennas mounted to an existingbuilding roof. No ground work will be performed a

Amend permit#com2009-11639 issued on 6-11-09 wplans#2009-654 to add the following additional work; one additional antenna to orginal permit per plans and code also extend original permit with original completion date of 12/11/09. Original permit descripti

Remove and replace 9 panel antennas mounted to an existingbuilding roof. No ground work will be performed at this site as per plans as per code. If installing suppression in equipment cabinet(s) then a separate permit is required.

(2) new microwave dishes and cables on rooftop as per plans as per code. If installing suppression system in equipment cabinet(s) then a separate permit is required.

Installing 1-25 kva transformer 1-1 a subpanel -2 pole amp breaker telephone conduit tenant sub meter as per code.

Adding 3 antennas and equipment on platform to the existing rooftop. If installing suppression system in cabinet(s) then a separate permit is required.

Use the plaza side of the best western hotel as a gift shop

Install cabinet inside existing penthouse and mount (1) panel antenna to the face of the penthouse as per plans as per code.

Use portion of existing truck wash for convenience store /carry out food store chain vending machine special retail cigarettes foodsubject

Install kitchen exhaust hood & duct as per code.

Run gas to char-broiler gas fryer gas griddle gas stove new faucetts on (3) comp sink ice machine popsi machine coffee machine cappacino machine hand sink fryer 105 0 btu char broiler 0 gas range 113 0 and gas griddle 000. As per c

Install wet chemical fire system in kitchen exhaust hood. As per code.

Reinstate permit #com2005-21586 for thirty (30) days for final inspectionoriginal permit description:(com2005-21586)maintenance upgrade- replacement of 9 antennas with 6 antennas on a existing rooftop and install one equipment cabinet inside of existing

Reconfigure 5 outlets & add 5 new outlets install 4 phone outlets & install 2 recessed lts with switch. As per code.

Reinstate permit # com2005-27732 for thirty (30) days for final inspection. Original permit description:(com2005-27732)amend permit # com2005-21586 issued on 8/18/05 with plan # 1034 to add electrical contractor as listed

(use) premises as a truck washing establishment

"1 illuminated storefront wall sign to read ""western union"" x 12 as per attached sketches as per code"

Install (36) communication lines. As per code.

Amend permit number com2006-13804 to show david b. Jarosinski as master gas fitteroriginal permit description:(com2006-13804)building is currently unoccupied (foremer) filling station w/retail building and service bays. Open canopy space at former pumps t

Temporary for construction: 1 8 a service 1 meter 1 6 a main w/ 4 2 amp meters as per code.

Amend permit number com2006-13804 to show david b. Jarosinski as master plumber and hugh reynold as hvac contractor issued on 7/6/06original permit description:(com2006-13804)building is currently unoccupied (foremer) filling station w/retail building and

Amend permit to name elect. Contractororiginal permit description:(com2006-13804)building is currently unoccupied (foremer) filling station w/retail building and service bays. Open canopy space at former pumps to be enclosed and converted to truck wash fa

Building is currently unoccupied (foremer) filling station w/retail building and service bays. Open canopy space at former pumps to be enclosed and converted to truck wash facility. Existing interior spaces to be slightly reconfigured and renovated for ne

Amend permit #com2005-25516 issued 12/2/05 w/plans 2005-1235 to add electrical contractor as stated above.

Installation of a diesel generator on a 12x15 concrete pad with retaining wall.

Amend permit # com2005-21586 issued on 8/18/05 with plan # 1034 to add electrical contractor as listed

Maintenance upgrade- replacement of 9 antennas with 6 antennas on a existing rooftop and install one equipment cabinet inside of existing bay 2 equipment cabinet

Installation of two illum sign cabinets reading best western. Sign one- 12 8 x 9 9 1/2 = 124 sq ft sign two 12 8 x 9 9 1/2

(use) continue to use premises for hotel (with conference center and pool) bus transit station covenience store and automobile gas station.

Amend permit #1860 issued 4/11/02 to add prime and electrical contractors

Add 2 amp sub panel - install (1) 125 amp 277v breaker in existing switchgear. Install (1) 1 1/4" conduit to new subpanel location. Install a 50kva transformer to get 120/240v 2 amps. Install new 2 a panel. Relocate (1) ckt from existing panel to new panel as per code.

Amend permit#com2009-11639 issued on 6-11-09 wplans#2009-654 to add the following additional work; one additional antenna to orginal permit per plans and code also extend original permit with original completion date of 12/11/09. Original permit description:(com2009-11639)(2) new microwave dishes and cables on rooftop as per plans as per code. If installing suppression system in equipment cabinet(s) then a separate permit is required.

Install 3 new antennas at an existing at&t telecommunication facility on the penthouse wall and antenna sled mount on roof. Install 1 cabinet on existing equipment platform. If installling supression system in equipment cabinet(s) then a separate permit is required.

Amend permit # com2009-23107 issued on 10/22/09 with plans # 2009-1305 to add contractor as listed aboveoriginal permit description:(com2009-23107)remove and replace 9 panel antennas mounted to an existingbuilding roof. No ground work will be performed at this site as per plans as per code. If installing suppression in equipment cabinet(s) then a separate permit is required.

Amend permit # com2009-23107 issued on 10-22-09 with plans # 2009-1305 to add the following additional work: 9 low voltage devices as per code. Original permit description:(com2009-23107)remove and replace 9 panel antennas mounted to an existingbuilding roof. No ground work will be performed at this site as per plans as per code. If installing suppression in equipment cabinet(s) then a separate permit is required.

Amend permit#com2010-23464 issued on 12-16- with plans# 2010-1416 to add prime contractor as listed above. Original permit description:(com2010-23464)install 3 new antennas at an existing at&t telecommunication facility on the penthouse wall and antenna sled mount on roof. Install 1 cabinet on existing equipment platform. If installling supression system in equipment cabinet(s) then a separate permit is required.

Run gas to char-broiler gas fryer gas griddle gas stove new faucetts on (3) comp sink ice machine popsi machine coffee machine cappacino machine hand sink fryer 105 0 btu char broiler 0 gas range 113 0 and gas griddle 000. As per code.

Replace faces on existing free standing sign total of 4 sq. Ft. As per plans sign "a" 162 sf sign "b" sq. Ftsign "c" 112 sftsign "d" 116 sft. Connect sign "b" . Work per code and per drawings.

Replace 3 existing toilets with new toilets. Replace existing bath hand sinks with new sinks. Replace 3 existing floor sinks with new floor sinks. Replace of existing 3/4" copper water lines with new tubing. All equipment same size/location as per code.

Interior work; 2 2 sq ft; interior work non structural alterations partition framing. Replace interior doors and walls office walls same size/location. Frame office walls ticket booth coatroom 4 bar areas per attached plans. Install suspended (drop) ceiling in office area repair all broken existing ceramic tile flooring as per plans as per code.

Remove/replace (3) unmanned equipment cabinets on rooftop. Remove/replace (5) antennas on rooftop and add (1) antenna to existing mont on rooftop. As per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Amend permit # com2011-19997 issued on 12-05-11 with plans # 2011-1357 to change electrical contractor. Original permit description:(com2011-19997)interior work; 2 2 sq ft; interior work non structural alterations partition framing. Replace interior doors and walls office walls same size/location. Frame office walls ticket booth coatroom 4 bar areas per attached plans. Install suspended (drop) ceiling in office area repair all broken existing ceramic tile flooring as per plans as per code.

Request for time extension on permit# com2011-17205 issued on 08/08/11 with original/amended completion date of 02/08/12original permit description:(com2011-17205)replace 3 existing toilets with new toilets. Replace existing bath hand sinks with new sinks. Replace 3 existing floor sinks with new floor sinks. Replace of existing 3/4" copper water lines with new tubing. All equipment same size/location as per code.

Install voice evacuation system in night club " whiskey jack" connect to existing building fire alarm low voltage only.

Non-structural alterations/exterior work - remove and replace (6) existing antennas on existing structure. Antenna will be located at same rad center as existing. Install 1 gps. As per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Amend permit#com2011-19997 issued on 12-5-11 w/completion date of 6-5-12 to extend for 6 months. (also must amend to add hvac contractor for hvac work)original permit description:(com2011-19997)interior work; 2 2 sq ft; interior work non structural alterations partition framing. Replace interior doors and walls office walls same size/location. Frame office walls ticket booth coatroom 4 bar areas per attached plans. Install suspended (drop) ceiling in office area repair all broken existing ceramic tile flooring as per plans as per code.

Swap 9 antennas remove 3 antennas install 6 rrh total of 12 antennas on building as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.

Original permit description:(com2015-08688)equipment upgrade (to existing telecoms facility) adding ancillary equipment to support the operation of existing antennas as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.

Replace existing water heater with ravpak water heater m#wh1-1631 same size and location. As per code.

Building is currently unoccupied (foremer) filling station w/retail building and service bays. Open canopy space at former pumps to be enclosed and converted to truck wash facility. Existing interior spaces to be slightly reconfigured and renovated for new shell tenant space. Per pud # 49 ordinance # 688 approved by the mayor and city council on 6/28/88 and final design approval of the planning commission of 6/30/06

Amend permit to name elect. Contractororiginal permit description:(com2006-13804)building is currently unoccupied (foremer) filling station w/retail building and service bays. Open canopy space at former pumps to be enclosed and converted to truck wash facility. Existing interior spaces to be slightly reconfigured and renovated for new shell tenant space. Per pud # 49 ordinance # 688 approved by the mayor and city council on 6/28/88 and final design approval of the planning commission of 6/30/06

Amend permit number com2006-13804 to show david b. Jarosinski as master plumber and hugh reynold as hvac contractor issued on 7/6/06original permit description:(com2006-13804)building is currently unoccupied (foremer) filling station w/retail building and service bays. Open canopy space at former pumps to be enclosed and converted to truck wash facility. Existing interior spaces to be slightly reconfigured and renovated for new shell tenant space. Per pud # 49 ordinance # 688 approved by the mayor and city council on 6/28/88 and final design approval of the planning commission of 6/30/06

Amend permit number com2006-13804 to show david b. Jarosinski as master gas fitteroriginal permit description:(com2006-13804)building is currently unoccupied (foremer) filling station w/retail building and service bays. Open canopy space at former pumps to be enclosed and converted to truck wash facility. Existing interior spaces to be slightly reconfigured and renovated for new shell tenant space. Per pud # 49 ordinance # 688 approved by the mayor and city council on 6/28/88 and final design approval of the planning commission of 6/30/06

1 illuminated storefront wall sign to read "western union" x 12 as per attached sketches as per code

Reinstate permit #com2005-21586 for thirty (30) days for final inspectionoriginal permit description:(com2005-21586)maintenance upgrade- replacement of 9 antennas with 6 antennas on a existing rooftop and install one equipment cabinet inside of existing bay 2 equipment cabinet

Addition of 3 remote radio heads to existing mounts no antennas will move as per plans as per code.

Install 3 antennas and 3 remote radio heads on existing roof top no ground work as per plans as per code.

Replacing 3 existing antennas with 3 new antennas adding 3 new remote radio heads. Replacing 3 existing radios with 3 new radios as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.

(use) continue to use entire premises for: hotel including restaurant and catering conference center and pool with outdoor seating and live entertainment throughout per pud ord. 86-688.

Non-strcutural alterations exterior work - install 2 illuminated wall sign - best western plus 13-10" x 10-4" = 142. 94 sq ft (x2); install 1 illuminated wall sign - best western plus 4-1" x 22-5" = 91. 53 sq ft; install 1 illuminated wall sign - best western plus 20-8" x 15-7" = 322. 05 sq ft; reface 2 monument signs - 5 8" x 4-11 1 2" = 12. 65 sq ft (x2). Remove & replace all hotel signs same location. As per drawing code.

Install 3 antennas and 3 remote radio heads on existing roof top no ground work as per plans as per code. Previously approved under permit #com2016-11225 (plan # 2016-963) issued on 06 07 16

Remove two panel antennas and install two panel antennas as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.

Addition of (3) remote radio heads to existing mounts no antennas will move as per plans as per code. Previously approved under com2016-10246 (plans #2016-856) issued on 06 03 16

Reinstate original permit.(original permit:com2017-01529:replacing 3 existing antennas with 3 new antennas adding 3 new remote radio heads. Replacing 3 existing radios with 3 new radios as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.)original permit description:(com2017-01529)replacing 3 existing antennas with 3 new antennas adding 3 new remote radio heads. Replacing 3 existing radios with 3 new radios as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.

Amend permit #1860 issued 4 11 02 to add prime and electrical contractors

Use portion of existing truck wash for convenience store carry out food store chain vending machine special retail cigarettes foodsubject

Remove replace (3) unmanned equipment cabinets on rooftop. Remove replace (5) antennas on rooftop and add (1) antenna to existing mont on rooftop. As per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Interior work (12 0 sq ft) - category i - non-structural alterations - interior demolition (remove non-bearing wall drywall ceiling tiles flooring and removal of debris and or equipment) as per code. Separate permit required for tenant fitout

Installation of two illum sign cabinets reading best western. Sign one- 12 8 x 9 9 1 2 = 124 sq ft sign two 12 8 x 9 9 1 2

Amend permit # com2005-21586 issued on 8 18 05 with plan # 1034 to add electrical contractor as listed

Amend permit #com2005-25516 issued 12 2 05 w plans 2005-1235 to add electrical contractor as stated above.

Amend permit to name elect. Contractororiginal permit description:(com2006-13804)building is currently unoccupied (foremer) filling station w retail building and service bays. Open canopy space at former pumps to be enclosed and converted to truck wash facility. Existing interior spaces to be slightly reconfigured and renovated for new shell tenant space. Per pud # 49 ordinance # 688 approved by the mayor and city council on 6 28 88 and final design approval of the planning commission of 6 30 06

Amend permit number com2006-13804 to show david b. Jarosinski as master gas fitteroriginal permit description:(com2006-13804)building is currently unoccupied (foremer) filling station w retail building and service bays. Open canopy space at former pumps to be enclosed and converted to truck wash facility. Existing interior spaces to be slightly reconfigured and renovated for new shell tenant space. Per pud # 49 ordinance # 688 approved by the mayor and city council on 6 28 88 and final design approval of the planning commission of 6 30 06

Reinstate permit # com2005-27732 for thirty (30) days for final inspection. Original permit description:(com2005-27732)amend permit # com2005-21586 issued on 8 18 05 with plan # 1034 to add electrical contractor as listed

Replace 3 existing toilets with new toilets. Replace existing bath hand sinks with new sinks. Replace 3 existing floor sinks with new floor sinks. Replace of existing 3 4" copper water lines with new tubing. All equipment same size location as per code.

Interior work; 2 2 sq ft; interior work non structural alterations partition framing. Replace interior doors and walls office walls same size location. Frame office walls ticket booth coatroom 4 bar areas per attached plans. Install suspended (drop) ceiling in office area repair all broken existing ceramic tile flooring as per plans as per code.

Non-structural alterations exterior work - remove and replace (6) existing antennas on existing structure. Antenna will be located at same rad center as existing. Install 1 gps. As per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Amend permit#com2009-11639 issued on 6-11-09 wplans#2009-654 to add the following additional work; one additional antenna to orginal permit per plans and code also extend original permit with original completion date of 12 11 09. Original permit description:(com2009-11639)(2) new microwave dishes and cables on rooftop as per plans as per code. If installing suppression system in equipment cabinet(s) then a separate permit is required.

Amend permit # com2009-23107 issued on 10 22 09 with plans # 2009-1305 to add contractor as listed aboveoriginal permit description:(com2009-23107)remove and replace 9 panel antennas mounted to an existingbuilding roof. No ground work will be performed at this site as per plans as per code. If installing suppression in equipment cabinet(s) then a separate permit is required.

Building is currently unoccupied (foremer) filling station w retail building and service bays. Open canopy space at former pumps to be enclosed and converted to truck wash facility. Existing interior spaces to be slightly reconfigured and renovated for new shell tenant space. Per pud # 49 ordinance # 688 approved by the mayor and city council on 6 28 88 and final design approval of the planning commission of 6 30 06

Amend permit # com2011-19997 issued on 12-05-11 with plans # 2011-1357 to change electrical contractor. Original permit description:(com2011-19997)interior work; 2 2 sq ft; interior work non structural alterations partition framing. Replace interior doors and walls office walls same size location. Frame office walls ticket booth coatroom 4 bar areas per attached plans. Install suspended (drop) ceiling in office area repair all broken existing ceramic tile flooring as per plans as per code.

Request for time extension on permit# com2011-17205 issued on 08 08 11 with original amended completion date of 02 08 12original permit description:(com2011-17205)replace 3 existing toilets with new toilets. Replace existing bath hand sinks with new sinks. Replace 3 existing floor sinks with new floor sinks. Replace of existing 3 4" copper water lines with new tubing. All equipment same size location as per code.

Amend permit number com2006-13804 to show david b. Jarosinski as master plumber and hugh reynold as hvac contractor issued on 7 6 06original permit description:(com2006-13804)building is currently unoccupied (foremer) filling station w retail building and service bays. Open canopy space at former pumps to be enclosed and converted to truck wash facility. Existing interior spaces to be slightly reconfigured and renovated for new shell tenant space. Per pud # 49 ordinance # 688 approved by the mayor and city council on 6 28 88 and final design approval of the planning commission of 6 30 06

Amend permit#com2011-19997 issued on 12-5-11 w completion date of 6-5-12 to extend for 6 months. (also must amend to add hvac contractor for hvac work)original permit description:(com2011-19997)interior work; 2 2 sq ft; interior work non structural alterations partition framing. Replace interior doors and walls office walls same size location. Frame office walls ticket booth coatroom 4 bar areas per attached plans. Install suspended (drop) ceiling in office area repair all broken existing ceramic tile flooring as per plans as per code.

(use) use portion of first floor as of esisting structure (approx. 12 0 sq. Ft.) as a nightclub (tavern-including live entertainment dancing) per pud ord 86-688.

Temporary for construction: 1 8 a service 1 meter 1 6 a main w 4 2 amp meters as per code.

Add 2 amp sub panel - install (1) 125 amp 277v breaker in existing switchgear. Install (1) 1 1 4" conduit to new subpanel location. Install a 50kva transformer to get 120 240v 2 amps. Install new 2 a panel. Relocate (1) ckt from existing panel to new panel as per code.

Install additional panel antennas & microwave dishes and (1) equipment cabinet platform on roof of existing telecom facility per plans & per code.