Install 145 low voltagecamera devices and install 106 low voltage access control devices as per code

Add (3) antennas. Swap (1) amp breaker with (1) amp breaker as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.

Replacement of (3) roof mounted antennas with (3) roof mounted antennas as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.

Replacing (3) obsolete antennas with new model type. Replacing (3) obsolete transceivers currently located at the base to the backside of the new antennas. As per plans and as per code. If installing suppression system in equipment cabinet then a separate

Amend permit# com2012-03523 issued on 03/30/12 with plans# 2012-248 to add electrical contractor as listed aboveoriginal permit description:(com2012-03523)non-structural alterations - adding (3) antennas to roof of existing building and placing an equipme

Interior work 15 sqft:run fiber conduit from basement to roof top install fiber control box on roof top. As per plans & as per code.

Remove and replace existing antennas on existing structure. Antenna will be located at same rad center as existing. No change in equipment cabinet at existing location as per code and plans. If installing suppression system in equipment cabinet then a sep

Non-structural alterations - adding (3) antennas to roof of existing building and placing an equipment cabinet and power panel on a 8 x /- grated platform on the rooftop as shown on the attached plans per bmza 2010-14 and such approval by the bmza

Remove 6 antennas & install 6 antennas and install 3 new equipment cabinets. As per plans and as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Remove and replace existing copper water lines couplings and valves that are deterirared and leaking in the first floor lobby ceiling area insulate piping that is replaced to eliminate future mainrenance condensation problems install new ceiling tiles a

Add low voltage control devices for boiler room asper code.

Install 6 panel antennas and 2 microwave dishes on existing building and 1 equipment cabinet on rooftop telecom facility per plans as per code. Per bmza 2011-51 approved 3/1/11. Right of entry from city required prior to issuing permit. If installing sup

Install new 2 amp sub panel. Install new 1 amp 277/4 volt switch into existing panel and new kva transformer to feed new subpanel. Install new conduit and feeders from existing panel to new subpanel. Install surge suppressor at new subpanel. Rel

Install new interior door and glass window. Relocate hvac diffuser install 2 receptacles on existing circuit and 1 switch for existing light fixture. Install (1ea) new telephone and date outlets. Relocate 1 existing sprinkler head and heating convector.

Replacement of 36 fan coils of same capacity as per code

Remove 1 25 0 gal u/g fuel oil storage tank; backfill and grade excavation; replace approximately 105 sq. Yd. Asphalt paving as per code.

Install (3) antennas at this existing telecommunications site as per plans & as per code. If installing suppression system in equipment cabinets then a separate permit is required.

Replace low voltage control devices for boiler room only as per code

Install (4) microwave dish antennas on an existing rooftop cell site as per plans and as per code. If installing suppression system in equipment cabinet then a separate permit will be required.

Install privacy slats in existing chain link fence remove dirt and debris from inside stone landscaping ring. Install chain link frnce. Repair welded gussed on top of ornamental fence which is cracked and split. Remove and replace section of concrete

Replace (22) pole lights with all new conduit and wire (energy saving) as per code

Replace old light fixtures with new energy saving light fixtures as per code.

Remove and replace existing sidewalk on housing development premises. Grind mis-aligned concrete joints on all concrete sidewalk as identified as per code

Install 1 new unmanned cabinet on rooftop and 1 antenna mounted to existing penthouse wall as per plans as per code.

Install hfc-227ea clean agent fire suppression system with associated low voltage detection and activation circuits. System to be installed in nextel telecommunications shelter system to be installed as per plan as per code.

Retro-fit of existing camera system. Adding 5 new cameras and replacing 6 existing cameras using existing drop.

Reinstate permit #com2005-18756 for thirty (30) days for final inspectionoriginal permit description:(com2005-18756)maintenance upgrade- replacement of 9 antennas with 7 antennas on a existing rooftop and install one equipment cabinet within a existing un

Reinstate permit # com2005-25885 for thirty (30) days for final inspection. Original permit description:(com2005-25885)amend permit # com2005-18756 issued on 7/13/05 w/ plan # 885 to add low voltage contractor as listed

Upgrade apollo shelter ( 12x ) as per plans and as per code. Per bmza 89-99x approved 3/30/99 amended 6/20/06

Install new feeder for existing elevator. As per plans.

Electrical work related to the upgrade of (2) passenger elevators.

Amend permit # com2005-18756 issued on 7/13/05 w/ plan # 885 to add low voltage contractor as listed

Maintenance upgrade- replacement of 9 antennas with 7 antennas on a existing rooftop and install one equipment cabinet within a existing unmanned equipment room as per plans

Replacement of old elevator equipment with new equipment. Installation of new elevator equipment to consist of: brake / rope gripper governor hoist cable guide shoes controller travel cable hall stations and signal fixtures control operating pane

Replace generator with 3 kw generator

Amend permit # com2004-22416 issued 10/18/04 with plan # 2004-11 to name plumbing contractor name as above

"install 6"" back flow prventer. For fire sprinkler system."

Installation of fire alarm as per plans

Renovate 52 existing apts to meet handicapped requirements. Seperate permit will be require for sprinkler system.

Retro-fit entire building with automatic fire sprinkler system. Per nfpa 13 & 13r 2002 editionseparate electrical permits required for fire pumps.

Install ckts

Install privacy slats in existing chain link fence remove dirt and debris from inside stone landscaping ring. Install chain link frnce. Repair welded gussed on top of ornamental fence which is cracked and split. Remove and replace section of concrete sidewalk. As per code.

Install new 2 amp sub panel. Install new 1 amp 277/4 volt switch into existing panel and new kva transformer to feed new subpanel. Install new conduit and feeders from existing panel to new subpanel. Install surge suppressor at new subpanel. Relocate one circuit from an existing panel into new subpanel as per plans & as per code.

Install new interior door and glass window. Relocate hvac diffuser install 2 receptacles on existing circuit and 1 switch for existing light fixture. Install (1ea) new telephone and date outlets. Relocate 1 existing sprinkler head and heating convector. Paint walls in new office remove and replace existing vct floor. All as per code.

Install 6 panel antennas and 2 microwave dishes on existing building and 1 equipment cabinet on rooftop telecom facility per plans as per code. Per bmza 2011-51 approved 3/1/11. Right of entry from city required prior to issuing permit. If installing supressions system in equipment cabinet(s) then a separate permit is required.

Amend permit# com2012-03523 issued on 03/30/12 with plans# 2012-248 to add electrical contractor as listed aboveoriginal permit description:(com2012-03523)non-structural alterations - adding (3) antennas to roof of existing building and placing an equipment cabinet and power panel on a 8 x +/- grated platform on the rooftop as shown on the attached plans per bmza 2010-14 and such approval by the bmza was given a time extension on 01/12/12 to 01/10/13 as per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Replacing (3) obsolete antennas with new model type. Replacing (3) obsolete transceivers currently located at the base to the backside of the new antennas. As per plans and as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Non-structural alterations - adding (3) antennas to roof of existing building and placing an equipment cabinet and power panel on a 8 x +/- grated platform on the rooftop as shown on the attached plans per bmza 2010-14 and such approval by the bmza was given a time extension on 01/12/12 to 01/10/13 as per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Remove and replace existing antennas on existing structure. Antenna will be located at same rad center as existing. No change in equipment cabinet at existing location as per code and plans. If installing suppression system in equipment cabinet then a separate permit is required.

Remove and replace existing copper water lines couplings and valves that are deterirared and leaking in the first floor lobby ceiling area insulate piping that is replaced to eliminate future mainrenance condensation problems install new ceiling tiles and grid damaged from water leaks approximately 15 sf as per code

Original permit description:(com2015-13199)replacement of (3) roof mounted antennas with (3) roof mounted antennas as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.

Relocate sprinkler heads new renovations. 22 relocates. As per code

Install ceramic tiles for (6) bathrooms in tub area. Install adjustable grab bar in (6) bathrooms. Install fold up grab bar in (6) bathrooms lower wall cabinets in one kitchen. Install (2) 24 grag bar and (1) 36 grab bar in (6) bathroom and paint (8) bathrooms

Install one toilet sink and faucet and tub faucet and one kitchen faucet.

Installing ckts replacing damaged panel with new panel

Install 6" back flow prventer. For fire sprinkler system.

Replacement of old elevator equipment with new equipment. Installation of new elevator equipment to consist of: brake / rope gripper governor hoist cable guide shoes controller travel cable hall stations and signal fixtures control operating panel door panels cab enclosure.

Reinstate permit #com2005-18756 for thirty (30) days for final inspectionoriginal permit description:(com2005-18756)maintenance upgrade- replacement of 9 antennas with 7 antennas on a existing rooftop and install one equipment cabinet within a existing unmanned equipment room as per plans

Replace 1 of 6" water service as per code

Add 1 additional antenna as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.

Install (3) new antennas and remove (3) existing antennas as per plans as per code.

Install (3) new antennas and remove (3) existing antennas as per plans as per code. Previous permit approved under plan # 2016-2691 issued 01 10 2017

Amend permit # com2004-22416 issued 10 18 04 with plan # 2004-11 to name plumbing contractor name as above

Replacement of old elevator equipment with new equipment. Installation of new elevator equipment to consist of: brake rope gripper governor hoist cable guide shoes controller travel cable hall stations and signal fixtures control operating panel door panels cab enclosure.

Amend permit # com2005-18756 issued on 7 13 05 w plan # 885 to add low voltage contractor as listed

Upgrade apollo shelter ( 12x ) as per plans and as per code. Per bmza 89-99x approved 3 30 99 amended 6 20 06

Reinstate permit # com2005-25885 for thirty (30) days for final inspection. Original permit description:(com2005-25885)amend permit # com2005-18756 issued on 7 13 05 w plan # 885 to add low voltage contractor as listed

Non-structural alterations - adding (3) antennas to roof of existing building and placing an equipment cabinet and power panel on a 8 x + - grated platform on the rooftop as shown on the attached plans per bmza 2010-14 and such approval by the bmza was given a time extension on 01 12 12 to 01 10 13 as per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Amend permit# com2012-03523 issued on 03 30 12 with plans# 2012-248 to add electrical contractor as listed aboveoriginal permit description:(com2012-03523)non-structural alterations - adding (3) antennas to roof of existing building and placing an equipment cabinet and power panel on a 8 x + - grated platform on the rooftop as shown on the attached plans per bmza 2010-14 and such approval by the bmza was given a time extension on 01 12 12 to 01 10 13 as per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Remove 1 25 0 gal u g fuel oil storage tank; backfill and grade excavation; replace approximately 105 sq. Yd. Asphalt paving as per code.

Install 6 panel antennas and 2 microwave dishes on existing building and 1 equipment cabinet on rooftop telecom facility per plans as per code. Per bmza 2011-51 approved 3 1 11. Right of entry from city required prior to issuing permit. If installing supressions system in equipment cabinet(s) then a separate permit is required.

Install new 2 amp sub panel. Install new 1 amp 277 4 volt switch into existing panel and new kva transformer to feed new subpanel. Install new conduit and feeders from existing panel to new subpanel. Install surge suppressor at new subpanel. Relocate one circuit from an existing panel into new subpanel as per plans & as per code.

Remove three existing antennas and replace with three new antennas add related ancillary equipment as per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Replace fire pump controller and transfer switch

Original permit description:(com2014-02266)adding (3) antennas (3) radio remote units (3) fiber cables (1) growth cabinet as per plans and as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Adding (3) antennas (3) radio remote units (3) fiber cables (1) growth cabinet as per plans and as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Remove (2)(e) cell antennas at each sector install (1)(n) aws and (1)(n) cell antenna at each sector install (2)(n) 1 5/8ÔÇ? Ava coax cables at each sector terminate cables in interior port shelter-hatch plate per vzw standards remove existing cell and

Original permit description:(com2012-13212)remove (4) existing antennas and replace with (4) new antennas. Decommission (2) existing radio cabinets. Install (1) new gps. As per plans as per code. If installing suppression system in equipment cabinet then

Remove (4) existing antennas and replace with (4) new antennas. Decommission (2) existing radio cabinets. Install (1) new gps. As per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Interior work 15 sqft: run fiber conduit from basement to roof top install fiber control box on roof top as per plans as per code.

Install 3 new atennas & replace 3 antennas and install new equipment cabinet on rooftop as per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

"exterior work; remove and replace damaged sections of existing concrete sidewalk approx. 1 sq. Ft. Two areas - 10w x 15l and 5w x 10l new concrete shall be on 4"" of gravel and 4"" thick; sidewalk on owners property; all work will be done as per co"

"amend permit#com2008-08507 issued on 7-15-09 with plans#2008-423 to change hvac contractor aslisted above. Original permit description:(com2008-08507)construction of a 21-8""l x 10-8"" w x 12-2 1/4""h shelter and standby generator on grade with associated"

Repair water service on private property as per code

Install (3) antennas at this existing telecommunications site as per plans & as per code. If installing suppression system in equipment cabinets then a separate permit is required.

"amend permit#com2008-08507 issued on7-15-09 with plans#2008-423 to add prime electrical and hvac contractor as listed original permit description:(com2008-08507)construction of a 21-8""l x 10-8"" w x 12-2 1/4""h shelter and standby generator on grade wit"

"request for time extension on permit # com2008-08507 issued on 05-28-08 with original completion date of 11-28-08. Original permit description:(com2008-08507)construction of a 21-8""l x 10-8"" w x 12-2 1/4""h shelter and standby generator on grade with as"

Installing (6) 4 pair cat 5 cables 1-2 amp subpanel 1-2 pole amp breaker for telecommunications site. As per code.

Adding 3 antennas and equipment on a steel platform to the existing rooftop. Per bmza 785-08 work done per plans and code. If installing suppression system in equipment cabinet(s) then a separate permit is required.

"construction of a 21-8""l x 10-8"" w x 12-2 1/4""h shelter and standby generator on grade with associated (12) sled mounted antennas. Per bmza 110-08."

Add unmanned cabinet to existing roof top and (2) dish antennas mounted to existing penthouse wall as per plans and code.

Amend permit # com2003-29047 relocate (2) cellular rafter antennas (sector1) to new sled mount & extend equipment platform per bmza 123-00x & per submitted plans

Amend permit #185654 issued on 4/16/02 to add prime contractor and electrical contractor

Request for time extension on permit # com2008-08507 issued on 05-28-08 with original completion date of 11-28-08. Original permit description:(com2008-08507)construction of a 21-8"l x 10-8" w x 12-2 1/4"h shelter and standby generator on grade with associated (12) sled mounted antennas. Per bmza 110-08.

Amend permit#com2008-08507 issued on7-15-09 with plans#2008-423 to add prime electrical and hvac contractor as listed original permit description:(com2008-08507)construction of a 21-8"l x 10-8" w x 12-2 1/4"h shelter and standby generator on grade with associated (12) sled mounted antennas. Per bmza 110-08.

Construction of a 21-8"l x 10-8" w x 12-2 1/4"h shelter and standby generator on grade with associated (12) sled mounted antennas. Per bmza 110-08.

Amend permit#com2008-08507 issued on 7-15-09 with plans#2008-423 to change hvac contractor aslisted above. Original permit description:(com2008-08507)construction of a 21-8"l x 10-8" w x 12-2 1/4"h shelter and standby generator on grade with associated (12) sled mounted antennas. Per bmza 110-08.

Original permit description:(com2012-13212)remove (4) existing antennas and replace with (4) new antennas. Decommission (2) existing radio cabinets. Install (1) new gps. As per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Remove (2)(e) cell antennas at each sector install (1)(n) aws and (1)(n) cell antenna at each sector install (2)(n) 1 5/8 ava coax cables at each sector terminate cables in interior port shelter-hatch plate per vzw standards remove existing cell and pcs diplexers at each sector install new cell and pcs diplexers at each sector diplexers to be mounted adjacent to and/or behind pcs antennas at each sector install (1) tma at each sector as per plans and as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Exterior work; remove and replace damaged sections of existing concrete sidewalk approx. 1 sq. Ft. Two areas - 10w x 15l and 5w x 10l new concrete shall be on 4" of gravel and 4" thick; sidewalk on owners property; all work will be done as per code.

Remove (3) wireless antennas and coaxial cabling. Remove (1) equipment cabinet and equipment platform. Remove ptc cabinet and associated conduit. Remove equipment grounding system. As per code. Demo only. Separate permit is req. To install antennas.

Remove and replace existing antennas and install four new antennas and install one addtional equipment cabinet on existing rooftop platform per plans per bmza 430-02 approved 10/15/02.

Amend permit#000179298 issued on 2-11-02 with plans#1352 to extend completion date from 2-30-03 to 9-5-03

Remove 3 cellular antennas and add 6 new cellular antennas per bmza 123-00x and per submitted plans.

Amend permit no. 179298 issued 2/11/02 to extend completion date to 12/9/03

Install 9 poles and lights in parking area

Non-structural alterations/exterior work - demolition only/removing cricket wireless antennas from existing rooftop as per code.

(use) continue to use portion of 1st floor for philanthropic and charitable institution (meals on wheels) packing and distribution site to meals on wheels clients. No cooking on site.(use originally approved per bmza 153-01x)

Install 3 new air 32 antennas 1 per sector for sector alpha beta and gamma alpha sector will be installed on a new sled as per plans as per code. If installing suppression system in equipment cabinet then separate permit is required.

Non-structural alterations exterior work - demolition only removing cricket wireless antennas from existing rooftop as per code.

Reinstate.(original permit:com2015-17613:remove three existing antennas and replace with three new antennas add related ancillary equipment as per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.)original permit description:(com2015-17613)remove three existing antennas and replace with three new antennas add related ancillary equipment as per plans as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Construction of a 21-8"l x 10-8" w x 12-2 1 4"h shelter and standby generator on grade with associated (12) sled mounted antennas. Per bmza 110-08.

Request for time extension on permit # com2008-08507 issued on 05-28-08 with original completion date of 11-28-08. Original permit description:(com2008-08507)construction of a 21-8"l x 10-8" w x 12-2 1 4"h shelter and standby generator on grade with associated (12) sled mounted antennas. Per bmza 110-08.

Amend permit#com2008-08507 issued on7-15-09 with plans#2008-423 to add prime electrical and hvac contractor as listed original permit description:(com2008-08507)construction of a 21-8"l x 10-8" w x 12-2 1 4"h shelter and standby generator on grade with associated (12) sled mounted antennas. Per bmza 110-08.

Remove (2)(e) cell antennas at each sector install (1)(n) aws and (1)(n) cell antenna at each sector install (2)(n) 1 5 8 ava coax cables at each sector terminate cables in interior port shelter-hatch plate per vzw standards remove existing cell and pcs diplexers at each sector install new cell and pcs diplexers at each sector diplexers to be mounted adjacent to and or behind pcs antennas at each sector install (1) tma at each sector as per plans and as per code. If installing suppression system in equipment cabinet then a separate permit is required.

Amend permit#com2008-08507 issued on 7-15-09 with plans#2008-423 to change hvac contractor aslisted above. Original permit description:(com2008-08507)construction of a 21-8"l x 10-8" w x 12-2 1 4"h shelter and standby generator on grade with associated (12) sled mounted antennas. Per bmza 110-08.

Amend permit #185654 issued on 4 16 02 to add prime contractor and electrical contractor

Remove and replace existing antennas and install four new antennas and install one addtional equipment cabinet on existing rooftop platform per plans per bmza 430-02 approved 10 15 02.

Amend permit no. 179298 issued 2 11 02 to extend completion date to 12 9 03