STANDBY ELECTRICAL SYSTEMS INC

3744 26th St Chicago Il
Service riser hit by vehicle in alley area. Remove existing riser and reinstall new riser and side protection.

3351 Addison St Chicago Il
Existing york rtu has 2oo amp feed fused at125 amps on it and is being removed with and replaced with new unit using same electrical feed.

3259 66th St Chicago Il
Upgrade service from 1 amps to 2 amps. Electrical feed for hot tub at amps 2 volts ,neutral and ground.

10201 Stony Island Ave Chicago Il
Extend existing boiler feeds 2 feet into new boiler control panel.

12936 Exchange Ave Chicago Il
Add sump pump circuit,washer dryer circuit and dishwasher circuit with disconnect switch

47 Kedzie Ave Chicago Il
The south pole in parking lot in front of city of chicago space needs to be repaired. This pole is the first pole to be fed from buildings house panel in rear of building. The conduit needs to be repaired in the ground. A break in the raceway exists.

1926 95th St Chicago Il
Provide 2 amp three phase overhead meter and 42 circuit panel

5153 Pulaski Rd Chicago Il
Provide 2 amp 3 phase overhead service with 42 circuit panel . Existing space was split and power needs to be added for vacant space

2042 Fremont St Chicago Il
Removal and replace 3 rear outdoor light fixtures on rear deck and add an additional outdoor fixture on 2nd floor deck

19 Mohawk St Chicago Il
1 inch pipe feed from house to existing garage . Raceway is for future garage and will be rough piped to existing panels. No wiring at this time.

12936 Exchange Ave Chicago Il
Change existing 1 amp fusebox to 1 amp circuit breaker box, new ringless meter socket,supplemental ground,water ground, new garage feed from house to garage(underground), 3 duplex receptacles 2 existing 1 new circuit, repair microwave outlet,

3217 47th Pl Chicago Il
5 3 bank moved atm machine from 4762s kedzie to other side of mall to 3217w 47th place. Permit for line voltage electric was issued in june for 3217w 47th but didnt include low voltage. Inspector fahey wanted low voltage permits . The bank has hired standby electrical systems. Inc. To supervise the banks contractors to install the low voltage work. It would be cat5line,cat3 line, door strikes(2), card swipes(2) alarm panel,and low voltage interconnects.

1818 Rutherford Ave Chicago Il
Remove existing electrical service and update to 1 amp circuit breakers

1466 56th St Chicago Il
Change electrical panel. Current meter socket is ringed and located in niche. Current conductors ran through concrete and are aluminum.

47 Kedzie Ave Chicago Il
"change of electrical contractor for original permit#100604019"

6455 Kedzie Ave Chicago Il
Add 2 high pressure sodium on rear of building,remove light fixture and add watt high pressure sodium, add 2 porcelein light fixtures in stairwell on 2 3way switches,add 1 amp power circuit.

20 95th St Chicago Il
Missing meter front and meter at rear of bulding. A new meter fitting will have to be installed as well as new meter from com ed

12936 Exchange Ave Chicago Il
Pipe and wire switches,recessed cans and duplex receptacles in basement. Pipe and wire low voltage raceways.

3418 61st Pl Chicago Il
Upon inspection in attic there is open wiring present. Bx cables will be landed in 19 boxes and piped and wired together onto existing circuits. Inspection of outlets and switches and change where needed.

2042 Fremont St Chicago Il
Removal and replace 3 rear outdoor light fixtures on rear deck and add an additional outdoor fixture on 2nd floor deck

2000 95th St Chicago Il
Missing meter front and meter at rear of bulding. A new meter fitting will have to be installed as well as new meter from com ed

1926 95th St Chicago Il
Provide 200 amp three phase overhead meter and 42 circuit panel

5153 Pulaski Rd Chicago Il
Provide 200 amp 3 phase overhead service with 42 circuit panel . Existing space was split and power needs to be added for vacant space

3744 26th St Chicago Il
Service riser hit by vehicle in alley area. Remove existing riser and reinstall new riser and side protection.

1900 Mohawk St Chicago Il
1 inch pipe feed from house to existing garage . Raceway is for future garage and will be rough piped to existing panels. No wiring at this time.

4770 Kedzie Ave Chicago Il
The south pole in parking lot in front of city of chicago space needs to be repaired. This pole is the first pole to be fed from buildings house panel in rear of building. The conduit needs to be repaired in the ground. A break in the raceway exists.

3351 Addison St Chicago Il
Existing york rtu has 2oo amp feed fused at125 amps on it and is being removed with and replaced with new unit using same electrical feed.

10201 Stony Island Ave Chicago Il
Extend existing boiler feeds 2 feet into new boiler control panel.

3259 66th St Chicago Il
Upgrade service from 100 amps to 200 amps. Electrical feed for hot tub at 50 amps 240 volts ,neutral and ground.

12936 Exchange Ave Chicago Il
Change existing 100 amp fusebox to 100 amp circuit breaker box, new ringless meter socket,supplemental ground,water ground, new garage feed from house to garage(underground), 3 duplex receptacles 2 existing 1 new circuit, repair microwave outlet,

12936 Exchange Ave Chicago Il
Add sump pump circuit,washer dryer circuit and dishwasher circuit with disconnect switch

6455 Kedzie Ave Chicago Il
Add 250 high pressure sodium on rear of building,remove light fixture and add 70 watt high pressure sodium, add 2 porcelein light fixtures in stairwell on 2 3way switches,add 1 20 amp power circuit.

1818 Rutherford Ave Chicago Il
Remove existing electrical service and update to 100 amp circuit breakers

1466 56th St Chicago Il
Change electrical panel. Current meter socket is ringed and located in niche. Current conductors ran through concrete and are aluminum.

3217 47th Pl Chicago Il
5 3 bank moved atm machine from 4762s kedzie to other side of mall to 3217w 47th place. Permit for line voltage electric was issued in june for 3217w 47th but didn't include low voltage. Inspector fahey wanted low voltage permits . The bank has hired standby electrical systems. Inc. To supervise the bank's contractors to install the low voltage work. It would be cat5line,cat3 line, door strikes(2), card swipes(2) alarm panel,and low voltage interconnects.