Install 6 duplex and 20a 120v circuit. Relocate 1 existing 200a 3 phase panel, install 4 exit and 4 emergency wall lights (replace existing), ( no new wiring)per 2008 nec

Replace panels reconnect loads, replace service entrance conductors 400a 3-phase 120 208v.

For the erection of one (1) flatwall sign 2-0" x 15-0" (spaces 22 & 23). All existing signs to be removed. Home furnishing store.

Installation of one goodman gas-fired furnace (115,0 btu) 93%, with 15 cfm ductwork (suite 1 - blue grass shopping center)

Manufacture and install one set of internally illum channel letters on raceway

Remove all existing "just kids signs & door vinyl decals. Sing #a (e02)-new static illuminatied channel letter wall sign -logo allstate= 37. 5sqft. Sign#b(n01) - new s f static illuminated flat wall sign -logo allstate agent name&#=16. 2sqft. Sign #c(e03)- new window vinyl decal-agent name number=3. 0sqft. Window area=64sqft vinyl coverage 5%. Sign#d(e04) - new window vinyl decal- hours of operation = 3. 0sqft glass area = 15. 4sqft vinyl coverage 19. 5% as per attached plans

Install 2 toilet and 2 lavatory

Installation of 4 wc,3 lav,1 urinal,33 floor drains,2 trench drains,1 mop sink,7 grease traps,(5)3 comp sinks,(3)2 comp sinks,2 bowl sinks,9 hand wash sinks,1 kitchen sink and 4 clean out floor (supermarket)

Installation of new hvac system to include duct work connection to previously approved roof top units and installation of two (2) kitchen exhaust hoods as per approved plans. Separate permits required for hood suppression system

Wiring 6 rooftop 30a 3-phase 480v hvac units with disconnects. Installing 2 gfci rooftop receptacles.

For the installation of an upgraded steel roofing system to support new mechanical equipment as part of an existing grocery store.

For the installation of a compressor rack and install new refridgerant as per approved plans.

Remove lat roof, install roofing membrane for retail space.

Alterations to include toilet room improvements, ceiling finishes, partition improvements, new store front and new exterior doors.

Install ct cabinet, meter socket, 2 sets 3 cu, 150a mcb panel & grounding. Refeed existing 200a mcb panel.

Install one additional lennox gas packed rooftop unit in conjunction with ap#511169 512537 for roof top units & structural framing for dunnage

Asbestos removal abatement required prior to the commencement of any work. For level ii alteration to an existing tenant space, alteration to include the erection of parition walls, provide new layout and furnsihings throughout. All work to be done per approved plans. Separate permits required for mechanical, electrical and plumbing work.

For the installation of dunnage for proposed roof top units referenced in ap#511169. All work to be done in accordance with approved plans. If field condition vary, contact structural engineer prior to the start of any work.

For the erection of five (5) roof top units on existing roof with modified roof system as shown per approved plans. If field conditions vary contact structural engineer prior to the start of any work. Roof top units to be installed in accordance with manufacturers specifications. Separate permits required for all other mechanical work and electrical work. Please see ap#512537 for dunnage work.

To correct violation - remove & replace damaged metal door and frame at rear of building

Interior demo removing cabinets and 4 high partitions and minor drywall repairs

Add 1- 3 phase, 200a meter socket, 1- 200a service disconnect and re-connect 1- 3 phase sub-feeder and panel... In accordance with 2008 nec

Erect flat wall sign 3x36

Furnish and install wiring as per attached drawings. All wiring shall comply with 2008 nec codes (east district)

Computing tenant fir out as per plan,29 flouresent light,4 exit signs,receptacles and switches,existing 100amp 3 phase service,existing branch circuitry re connected,6 receptacles on demizing wal 1-24 circuit 3 phase sub panel 100amp electric room as per 2008 nec

1st floor bathroom--rearrange existing wiring for 1 gfci, 1 switch for exhaust fan, 1 switch for lights and rearrange light fixtures (as per 2008 nec)

200a 3-phase service, 42 circuit panel, lights, 6 receptacles, 2 exit signs & 2 emergency lights.

Replace 2 existing parking lot pole light fixtures at the bank with led fixtures

Manufacture and install one set internally illuminated channel letters on raceway

1 set of illum channel letters to wall. 1 flat wall sign. Reface exsiting tenant panel to pylon sign

For removal of one (1) existing flatwall sign. For the erection of two (2) accessory flatwall signs as per plans.

Furnish and install fire alarm per 2008 nec & nfpa 72(shopping center)